24V 100W MEAN WELL CLG-100-24 LED Power Supply 24V 4A CLG-100 CLG Series UL Certification Enclosed Switching Power Supply

24V 100W MEAN WELL CLG-100-24 LED Power Supply 24V 4A CLG-100 CLG Series UL Certification Enclosed Switching Power Supply

$106.99
Skip to product information
24V 100W MEAN WELL CLG-100-24 LED Power Supply 24V 4A CLG-100 CLG Series UL Certification Enclosed Switching Power Supply
  • 24V 100W MEAN WELL CLG-100-24 LED Power Supply 24V 4A CLG-100 CLG Series UL Certification Enclosed Switching Power Supply
  • 24V 100W MEAN WELL CLG-100-24 LED Power Supply 24V 4A CLG-100 CLG Series UL Certification Enclosed Switching Power Supply
24V 100W MEAN WELL CLG-100-24 LED Power Supply 24V 4A CLG-100 CLG Series UL Certification Enclosed Switching Power Supply

24V 100W MEAN WELL CLG-100-24 LED Power Supply 24V 4A CLG-100 CLG Series UL Certification Enclosed Switching Power Supply

$106.99
 
Model CLG-100
Series CLG-100-24
Output Dc Voltage 24V
CONSTANT CURRENT REGION Note.7 18 ~ 24V
Rated Current Note.5 4A
Rated Power Note.5 96W
Ripple&Noise(max) Note.2 150mVp-p
Voltage ADJ.Range Fixed. Can be modified between 0% ~ -15% rated output voltage
CURRENT ADJ. RANGE Fixed. Can be modified between 3% ~ -25% rated output current
Voltage Tolerance Note.3 ±3.0%
Line Regulation ±1.0%
Load Regulation ±2.0%
Setup,Rise Time 500ms, 80ms / 230VAC 1200ms, 80ms / 115VAC at full load
HOLD UP TIME (Typ.) 60ms / 230VAC 30ms / 115VAC at full load
Input Voltage Range Note.4 90 ~ 295VAC 127 ~ 417VDC
Frequency Range 47-63Hz
Efficiency(typ.) 88.5%
Ac Current(typ.) 20V ~ 48V:1.1A/115VAC 0.55A/230VAC 0.45A/277VAC
Inrush current(typ.) COLD START 40A(twidth=1030μs measured at 50% Ipeak) at 230VAC
leakage Current <0.75mA / 240VAC
Protection Over Current(typ.) 95 ~ 102%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Over Voltage 27 ~ 34V
Protection type : Shut down and latch off o/p voltage, re-power on to recover
Environment Working Temp -30 ~ +70℃ (Refer to "Derating Curve")
Working Humidity 20-95%rh non-condesing
Storage Temp,Humidity -40~+85 , 10~95% RH
Temp.Coefficient ±0.03%°c(0-50°c)
Vibration 10~500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
Safety&EMC Safety Standard UL879, UL8750, UL1310, TUV EN61347-1, EN61347-2-13 independent, CAN/CSA C22.2 No. 223-M91(except for 48V), CSA C22.2 No. 250.0-08(except for 48V), CSA C22.2 No. 207-M89(except for 48V), IP67, J61347-1, J61347-2-13 approved
Withstand Voltage I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
Isolation Resistance I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC Emission Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (≧75% load) ; EN61000-3-3
EMI Immunity Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV), criteria A
Others MTBF 495.7Khrs min. MIL-HDBK-217F (25 )
Dimension 222.2*68*38.8mm (L*W*H)
Packing 1Kg;12pcs/13Kg/0.58CUFT
Warranty 2 years warranty
Datasheet
Note:
  • 1. All parameters not specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
  • 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
  • 3. Tolerance : includes set up tolerance, line regulation and load regulation.
  • 4.Derating may be needed under low input voltages. Please check the static characteristics for more details..
  • 5. This is the maximum possible output current and power, over load protection may be activated slightly below this level to comply with the requirement of UL1310 class 2.
  • 6. 3 years warranty is guaranteed for operating ambient temperature no higher than 68℃.
  • 7.Please refer to "DRIVING METHODS OF LED MODULE".
  • 8.Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18.
  • 9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
  • 10. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.

You may also like